Сisco WS-X6348-RJ-45

Сisco WS-X6348-RJ-45
Артикул: WS-X6348-RJ-45 Цена по запросу   Актуализировать цену

Технические характеристики:

Модули Catalyst WS-X6348-RJ-45 на 48 10/100 Fast Ethernet RJ-45 портов предназначены для коммутационных шкафов, в которых требуестя высокая плотность портов. 
 
Основные особенности:
  • Порты: 48x 10/100BASE-T RJ-45
  • Подключение к шине: Shared Bus
  • Форвардинг: Centralized

Ports per module

•48 ports (both modules). Ports are numbered (left to right):

–Top row, odd numbered ports 1 through 47.

–Bottom row, even numbered ports 2 through 48.

•4 port groups

•Port ranges per port group: 1-12, 13-24, 25-36, 37-48

Port connector type

RJ-45 (both modules)

Cabling distance

328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cable (both modules)

Buffer size

128 KB per port (both modules)

QoS

•Number of egress queues: 2

•Number of ingress queues: 1

•Number of thresholds per egress queue: 2

•Number of thresholds per ingress queue: 4

Maximum frame size

Up to 8092 bytes per frame (both modules)

Module oversubscription rate

N/A

Supervisor engine support

Supported on the following supervisor engines:

•Supervisor Engine 2

•Supervisor Engine 32

•Supervisor Engine 32 PISA

•Supervisor Engine 720

•Supervisor Engine720-10GE

Software support

•With Supervisor Engine 2—12.1(2)E

•With Supervisor Engine 32—12.2(18)SXF

•With Supervisor Engine 32 PISA—12.2(18)ZY

•With Supervisor Engine 720—12.2(14)SX

•With Supervisor Engine720-10GE—12.2(33)SXH

Queues per port

Both modules:

•Tx—2q2t

•Rx—1q4t

Chassis/slot restrictions

No chassis or slot restrictions; the modules can occupy any slot in any Catalyst 6500 or Catalyst 6500-E chassis.

Bus connection

32-Gbps shared bus (both modules)

Module upgrades available

 

PoE support

•WS-X6348-RJ45—Field upgradeable to Cisco prestandard with the WS-F6K-VPWR= PoE daughter card.

•WS-X6348-RJ-45V—Comes equipped with the WS-F6K-VPWR daughter card.

See the Cisco Catalyst 6500 Series Power over Ethernet Daughter Cards Field-Upgrade Installation Note for field upgrade procedures.

See Appendix A for further information on the PoE daughter cards.

Distributed forwarding support

Not supported.

Pluggable transceivers support

Not supported.

TDR support

Not supported.

Module front panel LEDs

STATUS

•Green—All diagnostics pass; the module is operational.

•Orange—The module is booting or running diagnostics.

An overtemperature condition has occurred. (A minor temperature threshold has been exceeded during environmental monitoring.)

•Red—The module is resetting. The switch has just been powered on or the module has been hot inserted during the normal initialization sequence.

An overtemperature condition has occurred. (A major temperature threshold has been exceeded during environmental monitoring.)

If the module fails to download code and configuration information successfully during the initial reset, the LED stays red; the module does not come online.

LINK

•Green—The port is active (the link is connected and operational).

•Orange—The module or port is disabled through the CLI command or the module is initializing.

•Flashing orange—The port is faulty and has been disabled.

•Off—The port is not active or the link is not connected.

PHONE

•Green—The PoE daughter card is installed and detected.

•Off—The PoE daughter card is not detected or is not installed.

Telegram-запрос